Front. Energy Res. Frontiers in Energy Research Front. Energy Res. 2296-598X Frontiers Media S.A. 1265906 10.3389/fenrg.2023.1265906 Energy Research Original Research Intelligent optimization algorithm-based electricity pricing strategy for smart building clusters Wang et al. 10.3389/fenrg.2023.1265906 Wang Hui 1 2 * Liao Xu 1 2 Ji Xiu 1 2 Gong Shanggao 1 2 Meng Xiangping 1 2 Wang Jiarui 3 1 School of Electrical Engineering and Information Technology, Changchun Institute of Technology, Changchun, China 2 National and Local Joint Engineering Research Center for Smart Distribution Network Measurement, Control and Safe Operation Technology, Changchun, China 3 State Grid JILIN Electric Power Research Institute, Changchun, China

Edited by: Praveen Kumar Donta, Vienna University of Technology, Austria

Reviewed by: Dipak Sah, GLA University, India

Kenneth E. Okedu, Melbourne Institute of Technology, Australia

V. B. Murali Krishna, National Institute of Technology, Andhra Pradesh, India

 *Correspondence: Hui Wang, wanghui841013@ccit.edu.cn 20 09 2023 2023 11 1265906 24 07 2023 17 08 2023 Copyright © 2023 Wang, Liao, Ji, Gong, Meng and Wang. 2023 Wang, Liao, Ji, Gong, Meng and Wang

This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.

With the continuous infusion of renewable energy sources, smart buildings have evolved from single-load characteristics into dual characteristics with both electric energy production and consumption capability. Concurrently, the peak and off-peak periods of electricity consumption are influenced by climatic factors, which leads to complexity and deviation from the time-of-use tariffs set by electricity markets, which consequently result in a loss of revenue from grid-based electricity sales. Thus, adopting an innovative pricing mechanism to offset the revenue deficit in the grid assumes paramount significance. Built upon a dual-layer framework that employs intelligent optimization algorithms, this study proposes a pricing strategy for introducing the retail electricity provider into smart building clusters with peer-to-peer power sharing as the core. First, the independent operation model of intelligent buildings and electric energy sharing model without the participation of retail power suppliers are respectively established. Subsequently, with the aim to minimize alliance costs, a novel energy sharing pricing model involving retail electricity suppliers is developed, and a combination of particle swarm optimization and alternating direction multiplier methods is used for distributed solutions within a representative model. This approach yields optimal energy sharing transaction volumes and pricing while ensuring the confidentiality of each participating entity. Lastly, from the perspectives of the power grid, retail electricity suppliers, and multi-building smart alliances, this study conducts simulation analyses of key parameters that influence the bargaining effectiveness of retail electricity suppliers. These parameters encompass the upper limit of pricing, market supervision coefficient, and discount coefficient associated with the grid-based electricity sales to suppliers. Through these analyses, the study further validates the efficacy of the proposed strategy.

 smart buildings peer-to-peer power sharing retail electricity provider market bargaining particle swarm optimization algorithm alternating direction multiplier method section-at-acceptance Smart Grids 1 Introduction

In recent years, the escalating concerns surrounding global warming and depletion of fossil energy reserves have garnered widespread attention. As a result, countries across the globe are steadfastly committed to advancing low-carbon economic practices. Within this context, addressing the escalating energy demands within China becomes pivotal, and this necessitates a robust exploration of renewable energy systems (Zhao et al., 2023). Consequently, smart buildings (SBs) with both electric energy production and consumption capability have emerged (Li et al., 2020). On the one hand, a single SB is usually composed of distributed photovoltaics; cogeneration of cooling, heating, and power; energy storage; and electricity/heating/cooling loads and can realize energy interaction with the outside world through the distribution network, the medium- and low-voltage gas distribution networks (Mofidi and Akbari, 2020). Moreover, the integration of multiple smart buildings can foster a smart building cluster system through energy interconnection. This collaborative framework empowers all SB participants to engage in peer-to-peer (P2P) power trading, effectively harmonizing power supply and demand dynamics, and thereby reducing reliance on the power grid (Liu et al., 2021; Zhou et al., 2021). The realization of such power sharing mechanisms bears immense significance in bolstering grid electricity sales revenue.

However, the daily net load profile of SBs often diverges from the temporal trend of time-of-use tariff prevalent in the broader power market, which culminates in a reduction in grid revenue. Both domestic and international research have diligently examined P2P power sharing within the smart building cluster paradigm (Singh and Baredar, 2017; Hu et al., 2019). Notably, efforts have been directed toward devising a Nash game model that orchestrates power trade negotiations among key stakeholders, encompassing wind, solar, and hydrogen subjects. Prior investigations have successfully employed the augmented Lagrangian multiplier method to optimize power sharing transaction volumes, characterized by their model simplicity and robust convergence (Ma et al., 2021). Further contributions have extended the P2P energy sharing model to an n-agent cooperation framework, broadening the versatility of the model (Wu et al., 2022).

Nonetheless, the inherent variability in photovoltaic power generation, intricacies of privacy preservation during P2P energy transactions, and self-interested pursuit of the lowest operating costs by SBs collectively exacerbate the challenges faced by the local power grid (LPG) in orchestrating efficient SB scheduling (Yang et al., 2018). To mitigate these complexities, the power grid urgently requires accurate predictions of the internal random source load of SBs and the judicious scheduling of SBs, so as to set the time-of-use price properly.

In the context of a conventional distribution network structure, the power grid exerts direct control over the pricing of power acquisition for lower-level buildings through the implementation of time-of-use electricity rates. This has led to concerns regarding the potential economic losses stemming from the increasing integration of renewable energy sources (Simkhada et al., 2022). As a result, there has been a growing interest in exploring the potential of introducing a retail electricity provider (REP) as an intermediary to manage this complex and contentious task on behalf of the grid. Literature pertaining to the introduction of REP highlights certain strategies to mitigate passive deceleration of the REP’s operations. Notably, the REP is established as an autonomous profit-generating entity, distinct from the local power grid (LPG), and is responsible for precise forecasting within the intricate lower-level energy system and a comprehensive exploration of the SB energy scheduling methodology (Wang et al., 2018; Xu et al., 2020). An optimized time-of-use electricity pricing scheme is formulated to promote the orderly transfer of flexible loads in the lower-level SB through the market mechanism, so as to meet the requirements of the upper-level power grid for peak shaving and valley filling and maximize its own operating benefits (Zhang et al., 2019). Within the realm of literature, a REP pricing model characterized by market oversight and user satisfaction considerations is proposed (Zhou et al., 2017; Immonen et al., 2020; Zhu et al., 2021). In this framework, each time the REP establishes an electricity price, the lower-level SB invariably seeks a scheduling plan that minimizes its individual operational costs at that specific electricity price. This approach facilitates the provision of a commodity demand for purchasing power vectors to the REP. Conceptually, this model, in taking the REP as a “wholesale-retail” role, seeks for a daily profit maximization model, which can be specifically depicted as “(wholesale price − retail price) * electric power vector and accumulation.” It is worth noting that solving this model entails addressing a non-trivial max–min non-linear problem, characterized by the intricate interaction between the electricity price variables and power variables, leading to computational intricacies (Zhang et al., 2021). Weishang et al. (2022) introduced a two-layer non-linear strategy grounded in the game theory for optimizing REP pricing, which effectively addresses the optimal pricing puzzle for individual SB. Moreover, Wang et al. (2023) illustrated that the double-layer max–min optimal pricing problem in between a single SB subject, REP, and the grid can be solved maturely through the strong duality theory and KKT condition theory. Nevertheless, notable gaps persist within the present body of research concerning the double-layer max–min optimal pricing problems that involve REPs, grid, and building clusters composed of numerous SB entities.

Addressing the inherent challenges within multi-smart building electricity price management, the power grid faces two unresolved issues: 1) as the prevalence of mixed renewable energy access rises, the P2P power sharing interaction costs may experience an upward trajectory, resulting in a limited total investment cost of the system. 2) The utilization of conventional optimization solvers to determine electricity transaction volumes per building raises concerns about user privacy. Moreover, the conventional grid’s electricity sales model fails to adequately account for the nuanced interests of lower-level user buildings, resulting in price conflicts.

To address these problems, this study introduces an optimal pricing strategy for REP in the context of SB clusters. Specifically, the layer particle swarm algorithm is employed on the upper layer to derive electricity price variables, while the alternating direction multiplier method (ADMM) is utilized on the lower level to allocate P2P power transaction volumes, thereby safeguarding the privacy of each participant. This dual-layer methodology not only enhances solution efficiency but also bolsters power grid revenue and reduces the system’s overall operational costs. The primary contributions of this study encompass the following:

1) Strengthening power interaction: by constructing a SB clusters power sharing model, the study augments power interactions among various buildings, thereby augmenting the assimilative capacity of wind and photovoltaic power sources.

2) Coordinated electricity pricing: the introduction of REP facilitates the harmonization of electricity prices between the upper-level power grid and lower-level buildings. In this process, the REP garners a portion of revenue while optimizing power grid sales income.

3) Enhanced solution methodology: a dual-layer solution methodology, integrating particle swarm optimization and the ADMM, is proposed. This approach ensures individual privacy while substantially expediting solution convergence.

The subsequent sections of this article are organized as follows: Section 2 builds the framework of P2P power sharing grid–operator–SB clusters; Section 3 presents an independent SB operation model; Section 4 establishes building clusters P2P power sharing model; case analysis and conclusions are shown in Section 5 and Section 6, respectively; and the overall workflow.

 2 Framework of SB power sharing and REP bargaining

This section intricately models the three distinct tiers: LPG, REP, and SB clusters, ensuring a robust safeguarding of internal equipment configuration and energy flows for each participant during the implementation of P2P transactions.

The upper-level LPG assumes the role of supplying external power support, thus fostering an equilibrium within the SB’s power system. At the middle level, REP, as a “wholesale-retail” intermediary, is responsible for setting the optimal electricity price and influencing SBs flexible load shift through market mechanisms (Wei and Lin, 2017; Schneiders et al., 2022), which alleviates the impact of LPG on SBS peak shaving pressure. The set electricity price by the REP is intricately calibrated within the bounds of market constraints, with a diligent pursuit of self-interest driving its determination. Situated at the lower tier, the SBs comprise multiple building entities. Each entity not only encompasses diverse energy production and consumption capabilities—ranging from electricity and heat to cold, gas, and carbon dioxide—but also boasts autonomous dispatching, independent management, and individual operators vested with the authority to trade in electricity. The overall operation framework is presented in Figure 1.

Power sharing framework of grid–REP–SBs.

 3 SB isolated operating model

In this section, the mathematical models, operational constraints, and minimum operating cost objective functions of key constituent devices in SBs are modeled. The lowest cost dispatch model for SBs under REP time-of-use tariff is mainly based on the SB isolated operation model without considering P2P, and then extends the SB alliance P2P power sharing model based on the ADMM. In addition, each smart building can dispatch autonomously with the goal of its own cost minimization and externally interacts only with the gas and electricity distribution networks.

3.1 Mathematical modeling of major equipment in SBs

Each isolated SB encompasses a diverse array of devices, exemplified in Figure 1. In this section, we only conduct detailed modeling of the three key equipment types, namely, the flue gas diversion carbon capture system, energy storage system, and temperature control system (Wang et al., 2018). The distributed photovoltaic model is presented in the works of Zhang et al. (2019). The electric heating demand response model is expounded upon in the literature of Rahman et al. (2021), while insights into the electric vehicle load model can be gleaned from the studies conducted by Ge et al. (2022). The coupling characteristics of the gas turbine electric heating system are meticulously documented in the literature authored by Wang et al. (2020).

3.1.1 Modeling of carbon capture systems for flue gas splitting

The carbon emissions of gas boilers and CCHP units are positively correlated with their thermal power output. C i , t C C H P = k E 2 C C C H P ⋅ E i , t C C H P + k H 2 C C C H P ⋅ H i , t C C H P C i , t G L = k H 2 C G L ⋅ H i , t G L , where C i , t C C H P and C i , t G L represent the carbon emission power of the cogeneration unit and the heat boiler in SB i at time t, respectively. E i , t C C H P and H i , t C C H P are the electric and thermal output power of the cogeneration unit, respectively. k E 2 C C C H P and k H 2 C C C H P present the carbon emission coefficients of the cogeneration unit. H i , t G L is the thermal output power of the heat boiler, and k H 2 C G L is the carbon emission coefficient of the heat boiler.

With the aim of advancing the attainment of the “carbon peaking, carbon neutrality” objective and mitigating erratic carbon emissions, an increasing number of SBs have embraced the integration of carbon capture devices subsequent to flue gas diversion. This strategic adoption facilitates the effective capture, storage, and controlled concentration of CO2. C i , t C C S = ϖ – ⋅ C i , t G L + C i , t C C H P ⋅ ε , where ϖ denotes the flue gas split ratio and ε denotes the carbon capture efficiency.

 3.1.2 Energy storage system model

In this section, a comprehensive model is constructed, encompassing diverse energy storage mechanisms within SBs, spanning electricity, heat, and CO2. These energy storage devices facilitate temporal energy displacement, effectively fostering dynamic power equilibrium adjustments. The energy storage model encompasses several key facets, which include energy storage and release power constraints, operational state uniqueness constraints, power–capacity coupling, capacity limitations, initial and final energy parity, and constraints on state transitions. O i , j , t E s s C P i , j E s s C min ≤ P i , j , t E s s C ≤ O i , j , t E s s C P i , j E s s C max O i , j , t E s s D P i , j E s s D min ≤ P i , j , t E s s D ≤ O i , j , t E s s D P i , j E s s D max O i , j , t E s s C + O i , j , t E s s D ≤ 1 S i , j , t + 1 E s s = S i , j , t E s s + η i , j E s s C P i , j , t E s s C Δ t + η i , j E s s D P i , j , t E s s D Δ t S i , j E s s min ≤ S i , j , t E s s ≤ S i , j E s s max S i , j , 1 E s s = S i , j , t e n d E s s ∑ t = 2 t e n d O i , j , t E s s C − O i , j , t E s s D − O i , j , t − 1 E s s C − O i , j , t − 1 E s s D ≤ O i , j E s s max where P i , j , t E s s C and P i , j , t E s s D present the energy storage and release power of the j-th energy storage device in SB i at time t, respectively. O i , j , t E s s C and O i , j , t E s s D are the state identification positions of its storage and release, and η i , j E s s C and η i , j E s s D denote the efficiencies of its energy storage and release, respectively. P i , j E s s C max and P i , j E s s C min are the upper and lower bounds of its storage power, respectively; P i , j E s s D max and P i , j E s s D min are the upper and lower bounds of its release power, respectively; and S i , j , t E s s is the amount of load energy. S i , j E s s max and S i , j E s s min represent the upper and lower limits of its energy storage capacity, respectively; S i , j , 1 E s s and S i , j , t e n d E s s present the amount of energy stored at the beginning and end of each day, respectively; and O i , j E s s max is the maximum number of storage and release state switching times per day of the energy storage device.

 3.1.3 Temperature control system model

As one of the main loads of SBs, the temperature control load is mainly used in pipeline heating or central air-conditioning refrigeration, etc., to control the temperature in order to achieve a satisfactory temperature felt by the human body. The indoor temperature fluctuation in building i is fundamentally contingent upon a linear interplay involving equipment heating and cooling power, as well as the disparity between indoor and outdoor temperatures. T i , t + 1 = T i , t + Δ T i , t Δ T i , t = k i H 2 T ⋅ H i , t T − L i , t T + k i H c h u a n d a o ⋅ T i , t w a i − T i , t Δ t , L i , t T = k i L ⋅ E i , t L T where T i , t and Δ T i , t are the temperature and amount of temperature change in SB i at time t, respectively; k i H 2 T presents the coefficient of proportionality between the indoor heating energy consumption and the amount of temperature change induced; k i H c h u a n d a o denotes the coefficient of thermal conduction property of the building construction; H i , t T and L i , t T represent the indoor heating and cooling power, respectively; T i , t w a i is the outdoor temperature. E i , t L T is the air conditioning and cooling power consumption, and k i L is the air conditioning electric and cold power conversion coefficient.

 3.2 Operational constraints model

In this section, only equipment power constraints, gas turbine climb constraints and start–stop constraints, demand-side response constraints, and multiple energy flow balance constraints are modeled.

3.2.1 Device power constraints

0 ≤ E i , t P V ≤ E i , t P V m p p t 0 ≤ P i , j , t D e v i c e ≤ P i , j D e v i c e max , where E i , t P V and E i , t P V m p p t are the PV power at time t in SB i and the upper limit of PV power, respectively. P i , j , t D e v i c e and P i , j , t D e v i c e max present the real-time power of device j and the upper limit of the output power.

 3.2.2 Gas turbine climbing constraints and start–stop constraints

0 ≤ E i , t + 1 C C H P − E i , t C C H P ≤ E i , p a p o C C H P O i , t C C H P ⋅ E i , min C C H P ≤ E i , t C C H P ≤ O i , t C C H P ⋅ E i , max C C H P , ∑ t = 1 t e n d − 1 O i , t + 1 C C H P − O i , t C C H P ≤ O i , max C C H P O i , t C C H P ∈ 0,1 where E i , p a p o C C H P denotes the upper limit of the climbing power of the CCHP unit in SB i; E i , max C C H P and E i , min C C H P are the maximum and minimum power limits of the gas turbine, respectively. O i , t C C H P can take the value of 1 or 0, representing the two states of running and stopping, respectively. O i , t C C H P is the limit of the maximum number of start–stop switching.

 3.2.3 Demand-side response constraints

− η i E D R ⋅ E i , t l o a d ≤ E i , t D R ≤ η i E D R ⋅ E i , t l o a d ∑ t = s t a r t e n d E i , t D R = 0 − η i H D R ⋅ H i , t l o a d ≤ H i , t D R ≤ η i H D R ⋅ H i , t l o a d ∑ t = s t a r t e n d H i , t D R = 0 , where E i , t l o a d and H i , t l o a d are the predicted values of electric heat load power at time t for SB i; η i E D R and η i H D R are the electric heat demand response load ratios of transferable types. The transferable demand response electric heat load has to satisfy the constraints of the full time period and of being zero, respectively.

 3.2.4 Multi-energy flow balance constraints

Smart buildings contain various energy flows such as electricity, heat, cold, natural gas, and carbon dioxide. Their power balance constraints are as follows: E i , t b u y + E i , t P V + E i , t C C H P + E i , t E s s D = E i , t s e l l + E i , t l o a d + E i , t D R + E i , t E V + E i , t L T + E i , t E s s C , where E i , t b u y and E i , t s e l l are the power purchased and sold, respectively, by SB i from the grid; E i , t P V is the photovoltaic power generation; E i , t E s s C and E i , t E s s D represent the charging and discharging power of the electric energy storage device, respectively; E i , t l o a d presents the electric load power; E i , t D R is the electric demand response power; E i , t E V denotes the power of electric vehicles; and E i , t L T is the power consumption of air conditioning and cooling. H i , t C C H P + H i , t G L + H i , t E s s D = H i , t l o a d + H i , t D R + H i , t H T + H i , t E s s C , where H i , t E s s C and H i , t E s s D are the heat storage and heat release power of the thermal energy storage device, respectively; H i , t l o a d is the heat load power; H i , t D R is the thermal demand response power; and H i , t H T is the heating power. G i , t b u y = G i , t l o a d + G i , t C C H P + G i , t G L , where G i , t b u y denotes the gas power purchased by SB i from the natural gas network; G i , t l o a d is the natural gas load; G i , t C C H P and G i , t G L present the gas consumption power of cogeneration units and thermal boilers, respectively.

 3.3 Minimum operating cost objective function model under isolated operation mode

Within this section, the focus lies on formulating the minimal operational cost W i 0 under the independent operation of SB i. The modeling primarily encompasses various cost components, which include the cost of electricity purchased and sold with the large grid W i D W , the cost of natural gas purchased from the low and medium voltage gas grid W i G W , the PV penalty cost for light abandonment W i P V , the cost of maintenance of the storage equipment W i W H , and the penalty cost for carbon emissions W i C . W i D W = ∑ t = 1 t e n d E i , t b u y ⋅ p t E b u y − E i , t s e l l ⋅ p t E s e l l W i G W = ∑ t = 1 t e n d G i , t b u y ⋅ p t G b u y W i P V = ∑ t = 1 t e n d p i P V ⋅ E i , t P V + p i P V c h e n g f a E i , t P V m p p t − E i , t P V W i W H = p i E E s s ⋅ ∑ t = 1 t e n d E i , t E s s C + E i , t E s s D + p i H E s s ⋅ ∑ t = 1 t e n d H i , t E s s C + H i , t E s s D W i C = ∑ t = 1 t e n d p C E s s ⋅ C i , t E s s + p C ⋅ C i , t C C H P + C i , t G L − C i , t E s s where p t E b u y and p t E s e l l present the time-of-use electricity price constants for SBs purchasing electricity from the grid and selling electricity; p t G b u y is the unit time-of-use price constant for natural gas purchased from the low- and medium-voltage gas network by SBs; p i P V is the photovoltaic unit power generation cost coefficient; p i P V c h e n g f a denotes the unit penalty cost coefficient for abandoned light; p i E E s s and p i H E s s represent the depreciation cost coefficients for the unit electrical and thermal energy storage power, respectively; p C E s s is the unit consumption cost of CO2 after carbon capture and storage; and p i C is the unit penalty cost of the CO2 emitted directly into the atmosphere. M i n i m i z e W i 0 = W i D W + W i G W + W i P V + W i W H + W i C s . t . 1 − 11

By employing the aforementioned formula, the minimum operational cost W i 0 for each individual SB within an isolated operational mode can be derived. This value serves as a reference point, representing the least favorable outcome for the forthcoming P2P power sharing model within the building clusters, which will be expounded upon in Section 4. The sum W s u m 0 of the total operating cost of multiple SBs for the isolated operation mode is expressed as W s u m 0 = ∑ i = 1 N W i 0 .

4 P2P power sharing model within SBs

Within this section, building upon the established framework of isolated operation models for multiple smart buildings, we employ the ADMM to formulate a multi-agent P2P power sharing paradigm within the SB clusters. Specifically, the modeling is carried out from four aspects: the necessary preparations for P2P power sharing among the bodies of SBs, REP bargaining model in the alliance mode, construction of a power sharing model based on the ADMM (with the aim of maximizing alliance benefits), and construction of the energy mapping contribution function to achieve reasonable redistribution of alliance benefits.

4.1 Preparation for introduction of P2P power sharing

To clearly demonstrate the process of electric energy sharing between N smart building bodies, N N − 1 auxiliary variables E i → j P 2 P , i ≠ j , i ϵ 1 , N are introduced, where E i → j P 2 P represents the electric power transmitted from SB i to SB j.

Given the considerable spatial span between SBs and the utilization of the extensive power grid for transmitting power in P2P transactions, the obligation to pay network connection fees arises. Consequently, this study establishes distinct unit costs for P2P power interactions based on varying spatial distances between SBs. This approach not only facilitates a more gradual and organized power interaction gradient between SBs but also enhances the convergence of the calculation example toward a singular solution. The transmission cost of electrical energy interaction between SB i and SB j can be calculated as follows: W i e p 2 p = ∑ j = 1 N ∑ t = 1 T m i → j E i → j , t P 2 P 0 ≤ E i → j , t P 2 P ≤ E i → j P 2 P , max E i → j P 2 P + E j → i P 2 P = 0 , j ≠ i , i ∈ 1 , N , j ∈ 1 , N where W i e p 2 p denotes the aggregated cost of electrical energy transmission incurred by SB i in its interactions with other SBs; m i → j P 2 P represents the unit cost of electrical energy transmission; and E i → j P 2 P , max defines the power limit of electrothermal transmission.

 4.2 REP bargaining model under SB model

Expanding upon the previously discussed introduction of P2P dynamics, the subsequent integration of REP serves to harmonize the vested interests between the upper-level power grid and users, mitigating the discord that may arise between the users and power grid owing to electricity pricing matters. Therefore, the forthcoming analysis will delve into a comprehensive modeling approach, examining both constraints and objective functions from a dual perspective.

4.2.1 Constraint modeling

Market monitoring constraints on the tariff mean value limits selected in this section: ∑ t = 1 t e n d φ t R E P s e l l A M S B ≤ α s c j d R E P ⋅ ∑ t = 1 t e n d p t E b u y φ min R E P s e l l A M S B ≤ φ t R E P s e l l A M S B ≤ φ max R E P s e l l A M S B , where φ t R E P s e l l A M S B defines the time-of-use tariff set by the REP, dictating the rate at which SBs procure electricity from the REP; p t E b u y is the time-of-use tariff in the electricity market; α s c j d R E P represents the market supervision coefficient, conventionally set at a value below 1. This deliberate choice fosters the perception among SB users that the REP pricing stands lower than the prevailing market rates, thus enhancing user satisfaction; φ max R E P s e l l A M S B and φ min R E P s e l l A M S B denote the upper and lower thresholds that govern the range within which the REP is authorized to establish tariff rates.

To ensure an adequate profit margin for the REP, electricity purchasing prices from the market are frequently subject to discounts: χ t R E P b u y G r i d = α z k R E P ⋅ p t E b u y , where χ t R E P b u y G r i d and α z k R E P represent the time-of-use tariff and discount factors utilized by the REP for the procurement of electricity from the grid.

The imperative of the REP to collaborate with the grid in demand management is evidenced by the necessity to devise electricity pricing mechanisms that influence the load redistribution within the building clusters. The disparity E P e a k 2 V a l l e y between peak and off-peak power transactions orchestrated by the REP from the SBs should align with the pre-established limit E l i m i t P e a k 2 V a l l e y , so as to assist the safe and stable operation of the power grid. Nonetheless, practical operation scenarios may introduce instances where the observed peak-to-valley discrepancy surpasses the established threshold or where further reduction of this variance is plausible. As a result, this study takes the existing peak-to-valley limit E l i m i t P e a k 2 V a l l e y as a benchmark; deviations beyond this benchmark invite corresponding penalties, whereas adherence to or reduction below the limit merits rewards. E P e a k 2 V a l l e y = max E R E P s e l l A M S B + max E R E P b u y A M S B W P e a k 2 V a l l e y = β ⋅ E P e a k 2 V a l l e y − E l i m i t P e a k 2 V a l l e y where E R E P s e l l S B s and E R E P b u y S B s are the time-of-use tariff variables for the sale and purchase of electricity from the REP to the SBs, respectively; β denotes the incentive and penalty coefficient of the distribution network on the effectiveness of the REP in regulating the peak-to-valley differential; and W P e a k 2 V a l l y is the penalty cost for exceeding the peak-to-valley differential.

 4.2.2 Objective function modeling

To enhance the profitability of the RE, under this electricity pricing scheme, a strategic approach that involves deducting the electricity procurement cost W R E P b u y G r i d incurred by the REP from the grid from the revenue W R E P s e l l A M S B amassed through REP’s electricity sales to smart buildings. Moreover, by factoring in the penalty incurred due to REP’s peak-to-valley differential surpassing the stipulated limit, a comprehensive calculation yields the actual net income denoted as W R E P , stemming from the REP’s pricing strategy: W R E P = W R E P s e l l A M S B − W R E P b u y G r i d − W P e a k 2 V a l l e y W R E P s e l l A M S B = ∑ t = 1 t e n d E t R E P s e l l A M S B ⋅ φ t R E P s e l l A M S B W R E P b u y G r i d = ∑ t = 1 t e n d E t R E P b u y G r i d ⋅ χ t R E P b u y G r i d .

Nonetheless, formula (18) exhibits a limitation by neglecting the presence of rooftop photovoltaic systems in SBs, which enables the scenario of electricity sales from the SBs to REP. To enhance the model’s accuracy, an enhancement is introduced whereby the REP procures the electricity price scalar φ R E P b u y A M S B from the SBs, while simultaneously vending electricity to the grid at the electricity price scalar χ R E P s e l l G r i d . Consequently, Eq. 18 can be refined as W R E P = W R E P s e l l A M S B − W R E P b u y G r i d − W P e a k 2 V a l l e y W R E P s e l l A M S B = ∑ t = 1 t e n d E t R E P s e l l A M S B ⋅ φ t R E P s e l l A M S B − E t R E P b u y A M S B ⋅ φ R E P b u y A M S B . W R E P b u y G r i d = ∑ t = 1 t e n d E t R E P b u y G r i d ⋅ χ t R E P b u y G r i d − E t R E P s e l l G r i d ⋅ χ R E P s e l l G r i d

Then, REP empirically develops an effective time-of-use tariff and analyzes it in comparison with the time-of-use tariff. Specifically, load forecasting has been employed, utilizing the ELMAN neural network, with a detailed reference available in the work of Eskandari et al. (2022). While this aspect is not the central focus of this study and thus will not be reiterated here. It is worth noting that the initial generation of electricity prices can be facilitated by employing algorithms such as deep learning. Such algorithms establish a correlation model between historical electricity prices and power dynamics, as evident in the works by Xie et al. (2023) and Liang et al. (2020). Moreover, a new purchase power variable of SBs can be brought into the model of fuzzy training to obtain the initial electricity price closer to the optimal value, thereby improving the convergence speed of calculation.

 4.3 Model for solving subproblem P of lowest SB operation cost

Due to its commendable convergence properties, straightforward formulation, and robustness, the ADMM stands as a suitable tool for resolving optimization challenges featuring variable equality constraints within a distributed framework. Therefore, this study uses the ADMM to solve the subproblem P of the minimum operating cost of the SB cluster, and uses the P2P power interaction in the resultant minimum cost dispatching scheme as the subproblem Q of the SB cluster revenue redistribution to calculate the contribution of each participant degree input parameters.

With the integration of electricity sharing transaction variables across intelligent buildings, the inherent output constraint intervals for each device remain unchanged. However, it is noteworthy that the resultant output values experience dynamic optimization in alignment with the electricity balance equation, influenced by the intricate interplay of energy interactions. After introducing the electricity sharing transaction variable between SBs, the new electricity balance equation of each SB in the system is defined as E i , t b u y + E i , t P V + E i , t C C H P + E i , t E s s D = E i , t s e l l + E i , t l o a d + E i , t D R + E i , t E V + E i , t L T + E i , t E s s C + ∑ j = 1 , j ≠ i N E i → j , t P 2 P .

After the introduction of power sharing, the minimum operating cost W i E P 2 P of SB i changes from Eq. 12 to M i n i m i z e W i E P 2 P = W i D W + W i G W + W i P V + W i W H + W i C + W i e p 2 p s . t . 1 − 7 , 9 − 11 , 14 , 20 .

After the introduction of P2P power sharing, the total operating cost W s u m E P 2 P of the SB cluster may be further reduced. The lowest total operating cost of SBs is expressed as W s u m E P 2 P = ∑ i = 1 N W i E P 2 P , min W s u m E P 2 P E i → 1 P 2 P , E i → 2 P 2 P , ⋯ , E i → j P 2 P , ⋯ , E i → N P 2 P s . t . 1 − 7 , 9 − 11 , 14 , 20 − 22 .

Then, using the equation constraint E i → j P 2 P + E j → i P 2 P = 0 of the power interaction variables, it can be solved based on the ADMM algorithm in a distributed manner. The specific steps are shown in Table 1. where L n P 1 is the lowest cost expression of SBs containing the augmentation term; λ k n is the Lagrange multiplier; k represents a distinctive identifier corresponding to the paired SB i and SB j. In the context of pairwise combinations among N subjects, the cumulative count amounts to N(N − 1). ρ denotes the augmentation term penalty constant, which can further improve the convergence efficiency through introduction into the square of the two-norm of the complementary error vector of the interaction quantity. n presents the current number of iterations, which should remain below its maximum value of n max . Additionally, the initial transaction volume for power sharing among SBs stands at 0, paralleled by the initial Lagrangian multiplier set at 0.

ADMM solving steps.

Algorithm ADMM
for iteration = 1, 2, …, N do
 for t = 1, 2, …, T do
  The augmented Lagrange multipliers for constructing the SBs minimum operating cost objective function are:
    L n P 1 = ∑ i = 1 N W i E P 2 P + ∑ k = 1 N ⋅ N − 1 λ k n E i → j P 2 P + E j → i P 2 P + ρ 2 ⋅ E i → j P 2 P + E j → i P 2 P 2 2 (24)
  Decomposed into a distributed iterative solution model for each SB.
    L n , i P 1 = W i E P 2 P + ∑ j = 1 N λ k n E i → j P 2 P + E j → i P 2 P + ρ 2 ⋅ E i → j P 2 P + E j → i P 2 P 2 2 s . t . 1 − 7 , 9 − 11 , 14 , 20 , 21 (25)
  Iteratively updating electrical energy shared transaction variables.
    E i → j P 2 P , n + 1 = argmin E i → j P 2 P L n , i P 1 s . t . 1 − 7 , 9 − 11 , 14 , 20 , 21 (26)
  end for
  Based on the transaction volume of electric energy sharing among new-generation smart buildings, iteratively update all N(N − 1) Lagrangian multipliers.
    λ k n + 1 = λ k n + ρ E i → j P 2 P , n + 1 + E j → i P 2 P , n + 1 (27)
Number of update iterations:
   n = n + 1 (28)
 Determine if the function has converged:
    ∑ t = 1 T ∑ i = 1 N ∑ j = 1 N E i → j P 2 P , n + 1 + E j → i P 2 P , n + 1 2 2 ≤ ς 或 n ≥ n max (29)
  If condition (29) is satisfied then the iteration terminates, otherwise return to (26) for the next round of iteration
  end for
  The convergence condition is satisfied or the maximum number of iterations n max is reached.
  Gain the electrical energy interaction E i → j P 2 P , e n d and the operating cost of each building W i E P 2 P , e n d
  Substituting W i E P 2 P , e n d into Eq. 22 yields the lowest total operating cost W s u m E P 2 P , e n d , retaining the electrical energy interaction cost W i e p 2 p , e n d of the main body of each building.

Progressively refine the power sharing transaction variables through iterative updates. During each distinct iteration, sequential iterative refinements are executed in accordance with the primary SB bodies' index i, ranging sequentially from 1 to n. Concurrently, the secondary intelligent building index, designated as j, traverses the same range from 1 to n, excluding instances where it equals i. It is noteworthy that electric energy interactions modified in the present evolutionary phase necessitate an update of variable values before their integration into the solution. This iterative process continues until all 2N(N − 1) electric energy interaction variables have been effectively updated.

 4.4 Subproblem Q solution model for rational redistribution of SB revenue

Within this section, we delve into the modeling of the revenue redistribution subproblem, denoted as Q, subsequent to the P2P power sharing framework of SBs. This modeling endeavor prominently encompasses three pivotal facets: 1) resolving the cumulative sum of redistributed benefits, thereby comprehensively addressing the overall quantum of benefits to be reallocated; 2) determining the proportional contribution ratios attributed to each individual SB participating in the P2P power sharing network; and 3) redistributing revenue according to the proportion of contribution to achieve benefits for all participants.

First, the total operating cost W s u m 0 of multiple intelligent buildings obtained in the isolated operation mode in Section 3 is subtracted from the total operating cost W s u m E P 2 P , e n d in the P2P power sharing model of the SBs in Section 4.2, and the total redistribution benefit Q is obtained. W D = ∑ i = 1 N W i 0 − ∑ i = 1 N W i E H P 2 P , e n d − ∑ i = 1 N W i e p 2 p , e n d

Subsequently, the energy mapping contribution function is constructed with reference to the economic knowledge, and the contribution ratio of each SB participating in P2P electric energy sharing is solved according to the electric energy interaction E i → j P 2 P , e n d . A contribution function that meets the following basic constraints is constructed:

1) Universality across all SBs partaking in the P2P power sharing network.

2) Predominance of energy supply-side contribution over energy-receiving counterpart.

3) Amplification of unit power sharing transaction contribution during peak demand periods relative to off-peak intervals.

4) Incremental contribution correlation with escalating transaction volume.

5) Convergence to zero contribution when transaction volume becomes null.

6) The contribution is always greater than or equal to 0.

The supplied electric energy E i P 2 P , s and received electric energy E i P 2 P , b during the energy sharing transaction process are defined as E i P 2 P , s = max 0 , ∑ j = 1 , j ≠ i N E i → j P 2 P , e n d E i P 2 P , b = min 0 , ∑ j = 1 , j ≠ i N E i → j P 2 P , e n d

Construct the energy sharing contribution θ i that can satisfy ①–⑥: θ i = ∑ t = 1 T p r i _ e t b u y E i , t P 2 P , s − p r i _ e t s e l l E i , t P 2 P , b

To further promote energy interaction, the linearly ascending contribution profile can be adeptly translated into an exponential upsurge. Furthermore, a normalization process can be administered to preempt the potential escalation of the power series beyond manageable proportions. τ i = e θ i ∑ N i = 1 θ i − 1 , where τ i denotes the final contribution of SB i.

Based on the contribution ratios of each SB actively engaged in the P2P power sharing, a judicious and equitable reallocation of revenue is effectuated. The benefit ϖ i E H P 2 P , e n d distributed by SB i can be expressed as ϖ – i E P 2 P , e n d = τ i ∑ N i = 1 τ i W D .

Then, the cost W i 0 of SB i under the isolated operation mode is subtracted from the redistributed benefits ϖ i E P 2 P , e n d in the cooperative mode, and the final actual operating cost W i 0 E P 2 P of the SB after participating in P2P power sharing is obtained. W i 0 E P 2 P = W i 0 − ϖ – i E P 2 P , e n d

Finally, the REP optimal pricing strategy for SB clusters with P2P power sharing has been modeled.

 5 Case analysis

In this section, we substitute the same load data into three models with different scheduling strategies, thus forming a control group. Then, a comparative analysis is carried out from the subproblem P of the minimum cost of the building cluster and the subproblem Q of benefit redistribution. Finally, the analysis of the three variables of the electricity price upper limit, market supervision and absorption, and REP’s discount coefficient for power purchases from the grid are, respectively, conducted, which proves the flexibility and necessity of REP’s bargaining and explains the impact on the revenue and costs of the SBs, grid, and REP.

5.1 Framework design of three models of smart buildings

From the perspective of progressive development, this section undertakes a rigorous comparative analysis based on models ①, ②, and ③: model ① is the isolated operation mode of multiple SBs under the large market electricity price, the objective function is Eq. 12, and the constraint conditions are formulas (1–11); model ② is the SB P2P electricity sharing mode under the large market electricity price, its objective function refers to Eq. 19, and the constraints are from formulas (1–7), (9–11), (14), (20–21), and (25–35); and model ③ is an REP bargaining and SB clusters P2P electricity sharing model, its objective function is Eq. 19, and the constraint conditions can be added to the constraints of model ② from formulas (15–17). The specific model comparison is shown in Figure 2.

Comparison of three smart building operation models.

 5.2 Model ③ calculation parameter

In this section, we mainly take the most complete model ③ as the core arithmetic example. The particle swarm optimization (PSO) algorithm is employed on the upper layer. The initial particle swarm is subject to a maximum of 20 iterations, and its population comprises 50 individuals. In Eq. 31, the upper limits of the REP-generated tariffs φ max R E P s e l l A M S B = 1.1 , the lower limits of the REP-generated tariffs φ min R E P s e l l A M S B = 0.4 , and the discount coefficient of the REP’s tariffs for purchasing from the grid α z k R E P = 1 . Amid the market surveillance and user satisfaction constraints delineated within Eq. 31, the market supervision coefficient α s c j d R E P = 1 for the upper limit of the ratio of the average value of REP pricing to the average value of time-sharing tariffs. The λ k 1 multiplier of the ADMM in Eq. 20 in the initialized SB coalition model is 0, and the incremental term penalty constant ρ = 10 e − 4 . The maximum number of iterations in Eq. 24 is 50, with a convergence accuracy of 0.001. Within this section, three SB entities are selected to establish an alliance for P2P power sharing. An illustrative analysis of the procedural intricacies, as delineated in Figure 2, is meticulously undertaken. The detailed configuration of equipment composition and constraints of power capacity pertaining to the three SBs are meticulously outlined, and the complementary parameters associated with the equipment landscape within these intelligent buildings find elucidation. The day-ahead prediction curves of PV and electricity–heat–gas–cooling loads are shown in Figure 3.

Day-ahead prediction curves of photovoltaic and electricity–heat–gas–cooling loads of smart buildings. (A) Smart building ①: residential smart building. (B) Smart building ②: industrial smart building. (C) Smart building ③: business smart building. (D) Electricity price of grid and the upper and lower limits of REP pricing.

 5.3 Analysis of results of lowest alliance operation cost subproblem P

This part is conducted within the computational environment provided by an Intel® Core™ i7-7700 CPU processor @ 3.60 GHz. The programming tool employed is MATLAB 2018b, complemented by the commercial solver Gurobi version 10.0.1 for intricate problem solving. The focal point of the calculation is a representative example, undertaken by combining the established initial parameters with the foundational parameters of model ③. The ensuing analysis involves the generation of iterative curves, further extending to the calculation of the electricity sharing transaction volumes for both model ② and model ③. These transactions are scrutinized in the pursuit of maximizing the return yielded by the REP, thus encapsulating the essence of the investigation.

5.3.1 Analysis of REP iterative revenue

To further analyze the impact of introducing REP on the revenue of the power grid and SBs, a comprehensive analytical framework is adopted. This bifurcated approach entails the utilization of the particle swarm algorithm at the upper layer, complemented by the application of the ADMM at the lower layer, facilitating iterative computations. The results of the REP’s iterative income curve of model ② are shown in Figure 4.

REP iterative income of smart buildings.

Figure 4 demonstrates the convergence within a 20-iteration threshold, effectively highlighting both the algorithm’s rapid convergence rate and its inherent logical coherence. Notably, with iterations below eight, the REP revenue undergoes swift transformation from a negative value to a substantially positive one, signifying the algorithm’s speedy convergence characteristics. By the 10th iteration, a steady income value is attained, a pivotal prerequisite for establishing the REP pricing framework governing the lower tier of electric energy sharing.

 5.3.2 Power sharing transactions before and after introduction of REP

The P2P power sharing transaction volume of each building before and after the introduction of the REP is shown in Figures 5A, B

P2P power sharing balance result. (A) Electricity sharing balance results before REP introduction. (B) Electricity trading balance results after REP introduction.

Evidently depicted in Figure 5A, a distinctive pattern emerges wherein residential buildings exhibit scattered electrical loads, manifesting a power surplus. Conversely, commercial and industrial structures contend with substantial load demands surpassing their intrinsic power output. The substantial transmission of electric energy from residential buildings to commercial and industrial structures results in escalated transmission costs. At the end of power sharing, if the load demand is still not met, buildings have to purchase power from the higher-level power grid. There is a power price game between the cost and the cost of power sharing. Figure 5B demonstrates that after the introduction of REP, a conspicuous reduction in power trading volume is observed, predominantly concentrated during peak photovoltaic output periods. This alteration aligns with a discernible decrease in power transmission costs, effectively signifying that REP pricing accomplishes two key objectives: indirect regulation of the electricity price-related tension between the power grid and building users, while concurrently diminishing energy loss expenses.

 5.4 Analysis of Q results of reasonably redistributing subproblem of alliance revenue

In this section, we integrate the aforementioned electric energy transaction volumes into the energy mapping contribution function, thereby facilitating a systematic realignment of benefits based on the contribution ratios of SBs within the P2P electric energy sharing interaction. Then, the comparison of the REP bargaining price and time-of-use electricity price after benefit redistribution and the actual operating cost results are respectively analyzed.

5.4.1 Comparative analysis of time-of-use tariffs before and after revenue redistribution

The comparison diagram between the optimal REP price and time-of-use tariffs obtained through the iterative calculation under the P2P power sharing model is shown in Figure 6.

Comparison of time-of-use tariffs of the grid and REP optimal pricing.

From Figure 6, it can be observed that during the two time periods [0–6] and [15–18], the REP pricing is slightly higher than the time-of-use tariff, and SBs purchase less electricity from the grid. This is because during these periods, most of the electricity supply of the SB is derived from the energy stored in the SB’s energy storage system from the previous day. In the [6–12] time period, the time-of-use electricity price experiences a significant increase, while the increase in REP pricing is comparatively minor. Moreover, the roof photovoltaic power generation within the SBs contributes to the electricity supply, thereby reducing the amount of electricity purchased from the main grid. During the [12–21] time period, there is a gradual increase in the amount of electricity purchased from the main grid in the [12–16] time period, followed by a decrease in electricity purchases from the main grid in the [16–21] time period. As a result, the pricing by the REP also adjusts accordingly, further demonstrating the REP’s ability to promptly respond to the demand-side users’ requirements and thereby enhance user satisfaction.

 5.4.2 Analysis of building operating cost before and after revenue redistribution

Referring to the data, the post-P2P power sharing scenario exhibits a decrease in operating costs for residential, industrial, and commercial buildings—14,282 RMB to 13,910 RMB for residential, 14,575 RMB to 14,187 RMB for industrial, and 14,356 RMB to 14,029 RMB for commercial structures. Despite the cost reductions, an issue of uneven distribution emerges. To address this concern, this study introduces the REP mechanism to rebalance benefits across these buildings. This undertaking involves calculating the contribution ratio via the energy mapping contribution function. Subsequently, this ratio is applied to each building entity, ensuring equitable benefit redistribution through REP participation. The P2P electricity, gas, and heat equilibrium post-redistribution is depicted.

The inclusion of the REP between the three buildings, along with their engagement in the equitable redistribution of benefits, yields substantial improvements. As observed, the pre- and post-redistribution alliance operating costs are significantly reduced, coupled with increased power grid and REP revenues. This underscores the imperative nature of benefit redistribution.

From Table 2, it is evident that after the reassignment of revenue among residential buildings, the costs have witnessed a reduction of 11.8%. By contrast, for industrial and commercial buildings, the operating costs exhibit a remarkable 29.1% and 52.5% decrease, respectively—both before and after benefit redistribution. This collective cost reduction engenders a substantial decrease in the overall system operating costs, aligning favorably with enhanced economic efficiency.

Analysis of smart buildings revenue redistribution results.

Building type Independent operating costs/RMB P2P power sharing cost (RMB) Contribution degree Proportion of redistribution benefits Redistribution of benefits (RMB) Actual operation cost after connection (RMB)
Residential building 14282 53.94 23615 38.9% 12771 1512
Industrial building 14575 34.23 11789 34.4% 11286 3289
Commercial building 14356 42.47 42376 28.7% 9411 4945
Total 43214 130.64 32780 100% 33468 9746
5.5 Analysis of factors affecting revenue and costs of power grid, REP, and SBs

The above example analysis only focuses on specific examples where the REP electricity price limit variable φ max R E P s e l l A M S B = 1.1 , φ min R E P s e l l A M S B = 0.4 ; the market supervision coefficient variable α s c j d R E P = 1 ; the discount coefficient variable of REP’s electricity purchase price from the grid α z k R E P = 1 . This analysis fails to entirely encompass the full flexibility inherent in REP market bargaining. To address this limitation, these three variables will be flexibly selected to analyze their different impacts on the bargaining effect of REP.

5.5.1 Influence analysis of electricity price limit variable

In this section, model ③ can be transformed into model ② when the electricity price limit variable of the REP bargaining model is taken as the grid large market electricity price constant φ max R E P s e l l A M S B = φ min R E P s e l l A M S B = χ t R E P b u y G r i d , the market supervision coefficient variable α z k R E P = 1 , and the discount coefficient variable of REP’s electricity purchase price from the grid α s c j d R E P = 1. In addition, under the conditions that the market supervision coefficient variables all take α z k R E P = 1 and the discount coefficient variables of the REP’s electricity purchase price from the grid all take α s c j d R E P = 1 , for the different combinations of the upper limit of the electricity price when the lower limit variable of the electricity price is 0.4, model ③ REP optimal market negotiation is carried out separately, and the results are shown in Figure 7.

Cost–revenue curve of each subject under different electricity price ceiling.

The depicted figure reveals that as the upper limit value of the electricity price increases, each cost and income value exhibits an upward trajectory. The purpose behind this analysis is to identify an electricity price limit where both grid income and REP income are maximized, thereby determining the optimal upper limit for electricity pricing. Notably, when the electricity price limit is below 0.8, the REP income turns negative, leading to suboptimal power grid income and reduced overall revenue. Moreover, the total cost of SBs consistently surpasses the power purchase expenses. This dynamic signifies effective power transaction utilization, concurrently reducing energy wastage within buildings.

 5.5.2 Analysis of influence of market supervision coefficients

In this section, different values of the market supervision coefficient variables are substituted into the REP optimal market price bargaining model when the REP power price limit variable φ max R E P s e l l A M S B = 1.1 , φ min R E P s e l l A M S B = 0.4 , and the discount coefficient variable of REP’s electricity purchase price from the grid α z k R E P = 1 . The results are shown in Figure 8.

Cost–revenue curve of each subject under different market supervision coefficients.

As shown in Figure 8, an increase in the market supervision coefficient leads to a general upward trajectory in both costs and revenues. When the supervision coefficient reaches 1.0, various costs and revenues stabilize, rendering the market incapable of effectively regulating returns and costs. Consequently, it becomes evident that a supervision coefficient below 1 effectively regulates both grid and REP revenues, ultimately yielding the optimal electricity price.

 5.5.3 Analysis of influence of discount coefficient variable on power purchase price of REP from grid

In this section, we substitute the different values of the discount coefficient variable α z k R E P of the REP’s electricity purchase price from the grid into the model ③ REP optimal market bargaining price when the REP power price limit variable φ max R E P s e l l A M S B = 1.1 , φ min R E P s e l l A M S B = 0.4 , and the market supervision coefficient variable α s c j d R E P = 1 . The results are shown in Figure 9.

Cost–revenue curve of each subject in the change of REP discount coefficient.

Figure 9 illustrates that as the REP power purchase discount coefficient rises, there is a marginal decrease observed in both the cost of SB clusters and the power purchase expenses. However, these trends tend to stabilize notably when the discount coefficient reaches 1.4. As the discount coefficient incrementally rises, there is a corresponding increase in power grid income, accompanied by a gradual decrease in REP income—potentially even resulting in losses. This underlines the significance of optimizing REP and grid revenue to foster the future development of a smart grid infrastructure.

 6 Conclusion

Addressing the challenge of load variability stemming from fluctuations in the peak-to-valley disparity within the expansive market, which is a critical concern impacting the power grid sales revenue, this study presents a pricing strategy of introducing the REP into SB clusters with P2P power sharing method. Through rigorous analysis of the computational data, the following insights have emerged:

1) By adopting the P2P power sharing approach, a notable 7.1% reduction in abandoned wind and solar energy within each lower-level building is achieved. This method curtails energy wastage through inter-building power transmission while concurrently minimizing the variance between load peaks and valleys.

2) The REP market pricing strategy introduced in this study effectively circumvents the revenue loss inherent in the conventional stepped time-of-use electricity pricing structure. Leveraging the REP, a harmonized supply–demand relationship between the upper-level power grid and lower-level building alliance is achieved, resulting in a commendable 12.4% reduction in alliance-wide costs. This strategy not only bolsters the overall economic efficiency of the system but also notably enhances user satisfaction across the various buildings.

3) For lower-level SB entities, the proposed methodology employs the PSO algorithm to derive preliminary electricity price variables at the upper layer. Subsequently, the lower layer employs the ADMM to achieve a distributed solution, thereby maximizing the collective benefits of the SBs and ensuring stringent privacy protection for each SB body. By establishing an energy mapping contribution function model that comprehensively considers the quantity, type, supply side, and time period of energy interaction, it further promotes the reasonable redistribution of revenues.

Data availability statement

Any data that support the findings of this study are included within the article. The data and structure of this article are sourced from Jilin State Grid Electric Power Co., Ltd. and supported by the “Land Scenery Three Gorges” major bidding project of Jilin Provincial Department of Science and Technology. The initial prediction data is included in the https://www.jianguoyun.com/p/DWDDkkIQtJvoCxieyJEFIAA.

 Author contributions

HW: Review and editing, Conceptualization, Supervision. XL: Original manuscript, software, verification. XJ: Review and editing, Supervision, Formal analysis. SG: Writing–Review and editing, Verification. XM: Writing review and editing, Methodology, Fund acquisition. JW: Review and editing, Project management, Resources.

 Funding

The authors declare financial support was received for the research, authorship, and/or publication of this article. This project is funded by Jilin Province’s “Land Scenic Three Gorges” high-quality development major science and technology project-park-level multi-microgrid system participating in key technology research projects for grid-friendly interaction (project number: 20230303003SF).

 Conflict of interest

Author JW was employed by State Grid JILIN Electric Power Research Institute.

The remaining authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

 Publisher’s note

All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors, and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.

 Abbreviations

SB, smart building; REP, retail electricity provider; WT, wind turbine; GL, gas load; AC, air condition; BES, battery energy storage; EL, electrical load; CS, carbon sequestration; GB, gas boiler; HL, heat load; P2P, peer-to-peer; LPG, local power grid; ADMM, alternating direction multiplier method; PV, photovoltaic; KKT, Karush–Kuhn–Tucker conditions; CCHP, combined cooling heating and power; EV, electric vehicle; HST, heat storage tank; TC, temperature-controlled load; PSO, particle swarm optimization.

 References Eskandari H. Kiani M. Zadehbagheri M. Niknam T. (2022). Optimal scheduling of storage device, renewable resources and hydrogen storage in combined heat and power microgrids in the presence plug-in hybrid electric vehicles and their charging demand. J. Energy Storage 50, 104558. 10.1016/j.est.2022.104558 Ge L. Du T. Li C. Li Y. Yan J. Rafiq M. U. (2022). Virtual collection for distributed photovoltaic data: Challenges, methodologies, and applications. Energies 15 (23), 8783. 10.3390/en15238783 Hu P. Ai X. Yang Z. Wu J. C. Guo L. S. Li Q. B. (2019). Co-optimized scheduling of integrated energy building clusters considering power sharing a few days ago. Power Autom. Equip. (08), 239–245. 10.16081/j.epae.201908047 Immonen A. Kiljander J. Aro M. (2020). Consumer viewpoint on a new kind of energy market. Electr. Power Syst. Res. 180, 106153. 10.1016/j.epsr.2019.106153 Li S. He Y. Peng H. Li H. (2020). 2011 A new species of the genus Pseudocercopithecus (Hymenoptera, Braconidae). Short-term optimal scheduling of intelligent building systems taking into account energy storage and controllable loads. J. Power Syst. Automation (07), 9–17. 10.19635/j.cnki.csu-epsa.000342 Liang Y. Guo C. Ding Z. Hua H. (2020). Agent-based modeling in electricity market using deep deterministic policy gradient algorithm. IEEE Trans. power Syst. 35 (6), 4180–4192. 10.1109/TPWRS.2020.2999536 Liu S. Zhou C. Guo H. Shi Q. Song T. E. Schomer I. (2021). Operational optimization of a building-level integrated energy system considering additional potential benefits of energy storage. Prot. Control Mod. Power Syst. 6 (1), 1–10. 10.1186/s41601-021-00184-0 Ma T. Pei W. Xiao H. Li D. Lv X. Hou K. (2021). 2011 A new species of the genus Pseudococcus (Coleoptera, Staphylinidae) from China. A cooperative operation method for wind-photo-hydrogen multi-principal energy system based on Nash negotiation theory. Chin. J. Electr. Eng. (01), 25–39+395. 10.13334/j.0258-8013.pcsee.200956 Mofidi F. Akbari H. (2020). Intelligent buildings: An overview. Energy Build. 223, 110192. 10.1016/j.enbuild.2020.110192 Rahman A. Aziz T. Deeba S. R. (2021). A time of use tariff scheme for demand side management of residential energy consumers in Bangladesh. Energy Rep. 7, 3189–3198. 10.1016/j.egyr.2021.05.042 Schneiders A. Fell M. J. Nolden C. (2022). Peer-to-peer electricity trading and the sharing economy: Social, markets and regulatory perspectives. Energy Sources, Part B Econ. Plan. Policy 17 (1), 2050849. 10.1080/15567249.2022.2050849 Simkhada S. Niraula M. Ojha P. R. Layalu Y. Singh A. Gwachha R. (2022). Time of use electricity pricing in power system planning and operation: Case study of Nepalese power system. Energy Rep. 8, 825–831. 10.1016/j.egyr.2021.11.101 Singh A. Baredar P. (2017). Power sharing and cost optimization of hybrid renewable energy system for academic research building. J. Electr. Eng. Technol. 12 (4), 1511–1518. 10.5370/JEET.2017.12.4.1511 Wang H. Wang C. Zhao L. Ji X. Yang C. Wang J. (2023). Multi-Micro-grid main body electric heating double-layer sharing strategy based on nash game. Electronics 12 (1), 214. 10.3390/electronics12010214 Wang P. Sun H. Hong X. (2018). “A unifying method to supervise market power in bilateral-auction electricity market,” in 2018 2nd IEEE conference on energy internet and energy system integration (EI2), 1–5. 10.1109/EI2.2018.8581914 Wang Y. Ma Y. Song F. Ma Y. Qi C. Huang F. (2020). Economic and efficient multi-objective operation optimization of integrated energy system considering electro-thermal demand response. Energy 205, 118022. 10.1016/j.energy.2020.118022 Wei Z. Lin M. (2017). Market mechanisms in online peer-to-peer lending. Manag. Sci. 63 (12), 4236–4257. 10.1287/mnsc.2016.2531 Weishang G. Yihua M. Xuexing Z. Haibing T. Yungaowa W. (2022). Study on optimal model of micro-energy network operation configuration considering flexible load characteristics. Energy Rep. 8, 10630–10643. 10.1016/j.egyr.2022.08.211 Wu J.-L. Lou P. Guan M.-Y. Huang C. Zhang W.-X. Cao Y.-C. (2022). Multi-microgrid power sharing operation optimization strategy based on asymmetric Nash negotiation. Grid Technol. (07), 2711–2723. 10.13335/j.1000-3673.pst.2021.1590 Xie J. Sage M. Zhao Y. F. (2023). Feature selection and feature learning in machine learning applications for gas turbines: A review. Eng. Appl. Artif. Intell. 117, 105591. 10.1016/j.engappai.2022.105591 Xu C. Wen F. Palu I. (2020). Electricity market regulation: Global status, development trend, and prospect in China. Energy Convers. Econ. 1 (3), 151–170. 10.1049/enc2.12020 Yang H. Wang L. Zhang Y. Tai H. M. Ma Y. Zhou M. (2018). Reliability evaluation of power system considering time of use electricity pricing. IEEE Trans. Power Syst. 34 (3), 1991–2002. 10.1109/TPWRS.2018.2879953 Zhang C. Yang T. Wang Y. (2021). Peer-to-Peer energy trading in a microgrid based on iterative double auction and blockchain. Sustain. Energy, Grids Netw. 27, 100524. 10.1016/j.segan.2021.100524 Zhang Z. Y. Yu T. Wang D. C. Pan Z. N. Zhang X. S. (2019). Integrated learning-based time-sharing tariff solution for commercial building clusters containing electrical heat. Chin. J. Electr. Eng. (01), 112–125+326. 10.13334/j.0258-8013.pcsee.181584 Zhao Y. Cai Q. Wang L. Song H. Yu J. Meng X. (2023). Changes in the electricity market under the participation of diverse participants and its supervision necessity analysis. Energy Rep. 9, 2013–2023. 10.1016/j.egyr.2023.04.141 Zhou B. Yang R. Li C. Cao Y. Wang Q. Liu J. (2017). Multiobjective model of time-of-use and stepwise power tariff for residential consumers in regulated power markets. IEEE Syst. J. 12 (3), 2676–2687. 10.1109/JSYST.2017.2718046 Zhou J. Li J. Ma H. Jiang D. Zhang H. (2021). 2011 A new species of the genus Pseudopelagicus (Hymenoptera, Braconidae, Pelaginae) from China. Distributed optimal scheduling of smart building clusters considering point-to-point power sharing. Power Autom. Equip. 10, 113–121. 10.16081/j.epae.202110029 Zhu Z. Kong L. Aisaiti G. Song M. Mi Z. (2021). Pricing contract design of a multi-supplier-multi-retailer supply chain in hybrid electricity market. Industrial Manag. Data Syst. 121 (7), 1522–1551. 10.1108/IMDS-09-2020-0543